The Single UNIX ® Specification, Version 2
Copyright © 1997 The Open Group

 NAME

putmsg, putpmsg - send a message on a STREAM

 SYNOPSIS



#include <stropts.h>

int putmsg(int fildes, const struct strbuf *ctlptr,
    const struct strbuf *dataptr, int flags);
int putpmsg(int fildes, const struct strbuf *ctlptr,
    const struct strbuf *dataptr, int band, int flags);

 DESCRIPTION

The putmsg() function creates a message from a process buffer(s) and sends the message to a STREAMS file. The message may contain either a data part, a control part, or both. The data and control parts are distinguished by placement in separate buffers, as described below. The semantics of each part is defined by the STREAMS module that receives the message.

The putpmsg() function does the same thing as putmsg(), but the process can send messages in different priority bands. Except where noted, all requirements on putmsg() also pertain to putpmsg().

The fildes argument specifies a file descriptor referencing an open STREAM. The ctlptr and dataptr arguments each point to a strbuf structure.

The ctlptr argument points to the structure describing the control part, if any, to be included in the message. The buf member in the strbuf structure points to the buffer where the control information resides, and the len member indicates the number of bytes to be sent. The maxlen member is not used by putmsg(). In a similar manner, the argument dataptr specifies the data, if any, to be included in the message. The flags argument indicates what type of message should be sent and is described further below.

To send the data part of a message, dataptr must not be a null pointer and the len member of dataptr must be 0 or greater. To send the control part of a message, the corresponding values must be set for ctlptr. No data (control) part will be sent if either dataptr (ctlptr) is a null pointer or the len member of dataptr (ctlptr) is set to -1.

For putmsg(), if a control part is specified and flags is set to RS_HIPRI, a high priority message is sent. If no control part is specified, and flags is set to RS_HIPRI, putmsg() fails and sets errno to [EINVAL]. If flags is set to 0, a normal message (priority band equal to 0) is sent. If a control part and data part are not specified and flags is set to 0, no message is sent and 0 is returned.

For putpmsg(), the flags are different. The flags argument is a bitmask with the following mutually-exclusive flags defined: MSG_HIPRI and MSG_BAND. If flags is set to 0, putpmsg() fails and sets errno to [EINVAL]. If a control part is specified and flags is set to MSG_HIPRI and band is set to 0, a high-priority message is sent. If flags is set to MSG_HIPRI and either no control part is specified or band is set to a non-zero value, putpmsg() fails and sets errno to [EINVAL]. If flags is set to MSG_BAND, then a message is sent in the priority band specified by band. If a control part and data part are not specified and flags is set to MSG_BAND, no message is sent and 0 is returned.

The putmsg() function blocks if the STREAM write queue is full due to internal flow control conditions, with the following exceptions:

The putmsg() function also blocks, unless prevented by lack of internal resources, while waiting for the availability of message blocks in the STREAM, regardless of priority or whether O_NONBLOCK has been specified. No partial message is sent.

 RETURN VALUE

Upon successful completion, putmsg() and putpmsg() return 0. Otherwise, they return -1 and set errno to indicate the error.

 ERRORS

The putmsg() and putpmsg() functions will fail if:
[EAGAIN]
A non-priority message was specified, the O_NONBLOCK flag is set, and the STREAM write queue is full due to internal flow control conditions; or buffers could not be allocated for the message that was to be created.
[EBADF]
fildes is not a valid file descriptor open for writing.
[EINTR]
A signal was caught during putmsg().
[EINVAL]
An undefined value is specified in flags, or flags is set to RS_HIPRI or MSG_HIPRI and no control part is supplied, or the STREAM or multiplexer referenced by fildes is linked (directly or indirectly) downstream from a multiplexer, or flags is set to MSG_HIPRI and band is non-zero (for putpmsg() only).
[ENOSR]
Buffers could not be allocated for the message that was to be created due to insufficient STREAMS memory resources.
[ENOSTR]
A STREAM is not associated with fildes.
[ENXIO]
A hangup condition was generated downstream for the specified STREAM.
[EPIPE] or [EIO]
The fildes argument refers to a STREAMS-based pipe and the other end of the pipe is closed. A SIGPIPE signal is generated for the calling thread.
[ERANGE]
The size of the data part of the message does not fall within the range specified by the maximum and minimum packet sizes of the topmost STREAM module. This value is also returned if the control part of the message is larger than the maximum configured size of the control part of a message, or if the data part of a message is larger than the maximum configured size of the data part of a message.

In addition, putmsg() and putpmsg() will fail if the STREAM head had processed an asynchronous error before the call. In this case, the value of errno does not reflect the result of putmsg() or putpmsg() but reflects the prior error.

 EXAMPLES

None.

 APPLICATION USAGE

None.

 FUTURE DIRECTIONS

None.

 SEE ALSO

getmsg(), poll(), read(), write(), <stropts.h>, STREAMS overview.

UNIX ® is a registered Trademark of The Open Group.
Copyright © 1997 The Open Group
[ Main Index | XSH | XCU | XBD | XCURSES | XNS ]